MENGENAL & MENGUKUR KOMPONEN ELEKTRONIKA



1. RESISTOR

Resistor adalah komponen elektronika yang terbuat dari arang yang bersifat sebagai tahanan / penghambat. Satuan Resistor adalah Ohm (Ω). Ukuran lainnya adalah Watt.

1 Mega Ohm (MΩ) = 1.000 Kilo Ohm (KΩ)
1 Kilo Ohm (KΩ) = 1.000 Ohm (Ω)

Resistor memiliki gelang warna yang merupakan kode ukuran dari resistor tersebut. Resistor terbagi menjadi :

a. Fixed resistor ( resistor biasa ) adalah resistor yang ukurannya tetap.

b. Variable resistor adalah resistor yang ukurannya dapat dirubah.


Variable resistor ada 5 jenis yaitu :
• Potensiometer • Trimmer Potensio (Trimpot) • NTC (Negative Temperatur Coefficient) : semakin panas hambatannya semakin kecil • PTC (Positive Temperatur Coefficient) : semakin panas hambatannya semakin besar • LDR (Light Dependence Resistor) : bila terkena cahaya maka hambatan akan mengecil Fungsi resistor dalam rangkaian elektronika :
• Sebagai beban rangkaian • Untuk membagi tegangan atau arus


Simbol Resistor dalam rangkaian :


Berikut daftar kode warna resistor :


Misal :

Resistor dengan gelang warna :

I. Coklat : 1
II. Hitam : 0
III. Merah : 00
IV. Perak : 10%

Jadi nilai resistor tersebut adalah 1000 Ohm atau 1 K Ohm dengan toleransi 10% artinya nilai aslinya bisa berkisar antara 900 Ohm – 1100 Ohm. Angka 900 didapat dari 1000 – (1000 x 10%) dan 1100 Ohm dari 1000 + (1000 x 10%).

GABUNGAN RESISTOR

Resistor Hubung Seri


Resistor yang dihubungkan seri nilai hambatannya adalah Rt = R1 + R2 + R ...
Misal : 1K Ohm + 1K Ohm = 2K Ohm




Resistor Hubung Paralel

Resistor yang dihubungkan paralel hasilnya adalah 1/Rt = 1/R1 + 1/R2 + 1/R .....
Misal : 1K Ohm diparalel dengan 1K Ohm hasilnya adalah 0,5 K Ohm.




Mengukur Resistor Dengan Multi Tester

1. Pastikan anda sudah melakukan zerro Ohm adj.
2. Putar batas ukur pada Ohmmeter (pastikan batas ukur lebih tinggi atau hampir sama dengan perkiraan resistor yang diukur).
3. Hubungkan probe ke masing-masing kaki resistor (bolak balik sama saja)
4. Lihat penunjukan jarum pada papan skala.





Kesimpulan Hasil Pengukuran1. Jarum menunjuk angka sesuai dengan ukuran aslinya : resistor baik
2. Jarum menunjuk angka lebih besar / kecil dari ukuran aslinya : resistor rusak
3. Jarum tidak bergerak sama sekali : resistor putus
4. Jarum menunjuk angka nol : resistor short

 Semoga Elektronika Dasar ini bermanfaat untuk rekan  WawasanElektronika semua & sukses terus rekan semua.

Sumber :  http://materi.progress-elektro.com

Link Belajar

LOKAL (bahasa indonesia)





LUAR (bahasa inggris)

TRAINING MANUAL
  • SONY dapat diperoleh dari http://www.epanorama.net/schematicsforfree/Sony/Video/index.php atau
  • Macam-macam Training manual dapat dicari lewat http://elektrotanya.com/?q=en  Caranya : Ketik pada kolom BRAND "merk" yang diinginkan (misalnya SAMSUNG). Ketik pda kolom MODEL :  "training manual". Pada kedua kolom ALL kosongkan saja. Kemudian klik SEARCH. Kalau belum pernah melakukan register hanya diperbolehkan maks 2 kali download setiap harinya. Kalau mau register diharuskan pernah kirim servive manual atau skema (yang belum pernah mereka miliki). Kalau tidak punya keduanya maka ada pilhan lain, yaitu memalui test dahulu (menjawab beberapa pertanyaan elektronik yang tidak terlalu sulit).


TENTANG SMPS
  • Basic SMPS Handbook On-Semi (download)
  • Philips technical guide (download)
  • Prinsip kerja IC regulator KSAQxxx atau STRF/G/W (dowmload)

MENGENAI BAGIAN DEFLEKSI HORISONTAL
  • Memahami kerja bagian horisontal (alamat)


MEMAHAMI SINYAL VIDEO
  • Perbedaan antara PAL,NTSC, SECAM (alamat)
  • Memahami tentang RESOLUSI gambar (alamat)
  • Memahami prinsip dasar sinyal video (download)
  • Memahami prinsip-prinsip sinyal video (alamat)



TENTANG CRT

Mars RAPI

Ciptaan: Didiek W. Soedjarwadi – JZ11AGY


RADIO ANTAR PENDUDUK INDONESIA
BERDIRI DEMI SUKSESKAN PEMBANGUNAN
MENUNAIKAN SEGALA TUGAS BANGSA
RAJIN DAN TEGUH BIJAKSANA

RADIO ANTAR PENDUDUK INDONESIA
BERJUANG DEMI KEJAYAAN NUSA
SIAGA DAN SEDIA MENGINDAHKAN
PANGGILAN MULIA IBU PERTIWI

REFF:
MUDA MUDINYA BERKOMUNIKASI
MENYAMBUNGKAN LIDAH KARYA
SERTA GEMAKAN KEKARYAAN
SUKARIA BEKERJA BERGOTONG ROYONG
TEKUN, LINCAH, TERTIB, RAMAH SERTA DAPAT DIPERCAYA
SELARAS PANCASILA

RADIO ANTAR PENDUDUK INDONESIA
BERSEDIA MENGORBANKAN JIWA RAGA
BERKOBAR SEMANGATNYA MERAH BARA
MESKI BERAT BEBAN DI PUNDAKNYA


Download:
Lirik dan Not Balok Mars RAPI
Mars RAPI versi Instrument
Mars RAPI versi Karaoke
Mars RAPI versi Vokal
Mars RAPI versi Instrument + Vokal
Lagu Wajib - Indonesia Raya.mp3
mengheningkan-cipta.mid


Terima kasih kepada:
JZ21AK – Om Ujuanto Yanto (Zebra)
JZ19RMC – http://jz19rmc.blogspot.com


Semoga Mars Rapi ini bermanfaat untuk rekan  WawasanElektronika semua & sukses terus rekan semua.

Sumber: http://jz21ak.blogspot.com

Experimental Dual Band High Gain Flower Pot Antenna

This experimental version is an extension of the basic Half Wave Flower Pot Antenna. Higher gain is achieved by adding an additional half wave element at the fundamental frequency (2m) coupled by a half wave phasing line to drive both half-waves in phase. Theoretically, this should provide an antenna gain of 3dBd at 2m.
The antenna is dual banded to operate on 70cm using the same sleeve technique as used on the dual-band basic Flower Pot. This results in the antenna operating with four half-waves in phase on 70cm and provides a theoretical antenna gain of 6dBd on 70.
Dimensions shown are for a 1st build prototype from a concept drawing and have yet to be refined. It started out as the 2006 Christmas break project but, unfortunately, I haven’t had time to refine the design. However, several members of my local radio club have built one of these and have reported success.
Experimental Dual Band High Gain Flower Pot dimensions
Experimental Dual Band High Gain Flower Pot dimensions
Assembly requires the same approach as used on the basic Flower Pot. The conduit is prepared and drilled as shown below.
Conduit Preparation Details
Conduit Preparation Details
The co-ax is pre-cut and trimmed prior to assembly as shown below.
Coax pre-Trim Details
Coax pre-Trim Details
The antenna radiating elements are constructed out of RG58 co-ax. It is essential that braided RG58 is used rather than foil-shielded co-ax (like that supplied by some of our local electronic hobbyist shops) as the bends required at the coil entry and exit points will likely damage and split the foil resulting in the antenna failing to perform.
The Sleeves can be made from any available high conductivity material such as aluminium kitchen foil, building (roof) sarking, disposable ‘baking’ trays, copper or brass shim etc. Materials such as steel or stainless steel are not suitable. The sleeves are fixed in place and protected from the weather and mechanical damage by covering them with UV resistant electrical tape or heat-shrink.
See original Flower Pot articles regarding protection of the coils from “White-Cockatoo Attack”.
VSWR as Measured on the Prototype:-
144 MHz 1.1:1
145 MHz 1.2:1
146 MHz 1.1:1
147 MHz 1.2:1
148 MHz 1.2:1
433 MHz 1.05:1
438 MHz 1.1:1
443 MHz 1.1:1
448 MHz 1.05:1

Dual Band Half-Wave Flower Pot Antenna

The basic half wave version of the Flower Pot antenna can be readily modified to dual band the antenna for operation on a band that is the (approximate) third harmonic of the fundamental resonance.
Operation on the third harmonic is achieved by using a sleeve technique so as to form quarter wave phasing sections (at the higher frequency) to end feed two half waves in phase at the third harmonic.
This arrangement provides useful gain (3dBd) on the higher band. The sleeve technique maintains the impedance matching for both bands and (probably fortunately) there is sufficient longitudinal impedance in the choke coil to provide the required isolation at the third harmonic.
The sleeve is applied after the basic antenna has been constructed.
Dimensions shown are for the (basic) 2m half-wave Flower Pot. The modification involves placing a co-ax phasing sleeve around the outside of conduit, positioned as shown.
Dimensions for a 2m half-wave Flower Pot
Dimensions for a 2m half-wave Flower Pot
The sleeve material can be aluminium (kitchen) foil, copper foil, brass shim, roof/building alfoil sarking or salvaged co-ax braid.
Foil sleeve
Before fixing the sleeve in place, check VSWR on 2m The sleeve should cause little if no change to 2m VSWR although it may appear to very slightly raise the resonant frequency; With the sleeve fitted, the VSWR should not be greater than 1.15:1 across the FM portion of band).
Then check VSWR across the 70cm (430 – 450 MHz) band. Expected VSWR readings will be less than 1.2:1 at band edges and less than 1.1:1 in band centre.
If VSWR is outside these limits, adjust position of sleeve (+/- 5mm max) and, if necessary, trim sleeve length to lower VSWR. When trimming sleeve length (dimension B) adjust dimensions A and C accordingly to keep centre of sleeve adjacent to feedpoint of the inner 2m dipole. However, little, if any, adjustment to the sleeve should be necessary. When satisfied with the VSWR, fix in place and protect the sleeve with UV protected PVC tape or heatshrink.
Heatshrinking the sleeve
Sleeve heatshrunk
Methods of dual banding the other versions are being developed and will be added to this website when available.


Source : http://vk2zoi.com

Double 5/8 Flower Pot Antenna

The Double 5/8 is a natural extension of the Single 5/8 and uses a 5/8λ element for both the top and bottom radiators.
The double 5/8 is a co-axially fed variation of the 1¼ wave (vertical) dipole shown in the adjacent diagram.
The double 5/8 is a co-axially fed variation of the 1¼ wave (vertical) dipole
The double 5/8 is a co-axially fed variation of the 1¼ wave (vertical) dipole
This antenna should not be confused with an in-phase 5/8λ over 5/8λ collinear. If it was horizontal, made of wire and cut for HF, an old-timer might call it an extended double Zep. However, in addition to having gain over a half wave dipole, it has a predictable 100 Ohm feedpoint impedance which is transformed close to 52 Ohms by a 75 Ohm quarter wave line transformer. About half of the line transformer is formed into a choke to act as a current BALUN to allow co-axial cable feed.

2m Double 5/8

We fashion this antenna into the Flower Pot co-axial design by constructing the antenna using RG59 75 OHM (solid dielectric) cable and bringing the feed co-axially down through the bottom element as shown in the diagram below.
2m Double 5/8
2m Double 5/8
The choke performs the dual role of providing isolation of the high impedance at the end of the bottom element and acting as a BALUN. Seven quarter waves of 75 Ohm cable are required for the bottom 5/8λ element and the coil winding. Seven 1/4 wavelengths of solid dielectric cable at 2m is 2.36m, to this add the 1.225m length needed for the top element to give a total length of 3.585m of 75 Ohm cable to construct a 2m antenna.

There are two ‘fiddly’ parts in making this antenna

The first is forming the 0.2λ section at the feed point of the bottom element. I ran a piece of braid on the outside of the cable sheath, carefully soldering this to the coax braid at the 0.2λ point and used heatshrink to hold it tight against the sheath. I assumed a velocity factor of 0.66 for this section. Care is needed when soldering to the coax braid (and this dictates the use of solid dielectric cable as foam or aircell dielectric will collapse away with the heat of soldering).
The second is ensuring that the braids don’t short at the feed point and I found a piece of heatshrink solved this. The sketch opposite also shows the detail at the radiator feedpoint and the piece of heatshrink acting as a separator.
Piece of heatshrink acting as a separator at the radiator feedpoint
Piece of heatshrink acting as a separator at the radiator feedpoint
Otherwise, building the antenna uses the same techniques as used in the basic half wave and single 5/8 versions.

Bandwidth

The antenna provides a low VSWR (less than 1.2:1) across the 2m band. But, if you like operating close to 1:1, a small variation in the bottom radiator length gives favour to either the high or low end of the band.
The VSWR plots are shown below.
VSWR plot for the Double 5/8
VSWR plot for the Double 5/8

Other frequencies

The Double 5/8 will scale to other frequencies, however the physical size and the mechanical properties of the conduit suggest that the design is more suited to the high VHF band.

Relative gain measurements between the designs

I do not have a means of accurately measuring antenna gain but set up each antenna with a switched attenuator in the feedline to a receiver. The attenuator was not ideal for this purpose, it had only 3,6 10 and 20 dB steps. However, using a local 2m beacon as a signal source and the basic l/2 Flower Pot as a reference and, within the limits of available accuracy and resolution of the steps of an S meter, I determined that the Single 5/8 had about 2dB gain over the l/2 antenna and the Double 5/8 was discernibly in excess of 3dBd gain (but, of course, much less than 6dBd).


Source : http://vk2zoi.com

Half-Wave Flower Pot Antenna

The diagram below shows the basic arrangement of the 2m Half-Wave version of the antenna. To construct the antenna, first select a suitable length of grey 25mm conduit (as a minimum 1m but if you make it longer, you will have more room below the coil to attach to your antenna support).

Basic arrangement of the 2m Half-Wave version
Basic arrangement of the 2m Half-Wave version
Drill two holes into the side of the conduit for the choke coil. The ‘top’ hole will be approx 925mm from the end (this distance is the length of the radiator plus a small clearance between its end and the end-cap). The spacing between the holes should be such that the coil turns will be firm and secure. Actual hole diameter and spacing will depend on the cable brand and/or where it was manufactured. It will be close to being two 6mm holes spaced 45mm apart but wind 9 turns temporarily on the conduit and take measurements.
Drilling conduit at an angle
Then take a suitable length of co-ax (I make mine using the one piece of cable, about 5 to 6m long, to reach from the antenna to the transceiver – the length is your choice). From one end, strip off 457mm of the outer sheath and braid to form the top element. It’s not a big problem if you end up with a length that’s a bit short, because a another piece of wire or the discarded braid can be soldered to the top to make the correct length.
Cutting coax sheathCleaned up coaxTop element
Using several “half-hitches”, tie a piece of fishing line (or similar, thin nylon line), say about half a metre long, to the top of the upper element. This line will be used to pull the radiator taut, it will clip over the top of the conduit and be clamped by the end cap.
fishing-line
Now measure 447mm down from the feedpoint (the point where the braid/outer sheath now starts); this is the distance to the start (or top) of the choke coil and mark this position on the coax with a piece of tape, string, paint spot, or whatever, so as to be a reference/stop point when inserting the cable into the conduit.
Bottom coax
The antenna is assembled by inserting the radiating portion (together with the piece of nylon line) through the top coil hole and pushing it upwards until the aforementioned reference/stop point disappears into the hole.
Feeding coax
Fish-out (pun intended) the nylon line and by pulling it taut, temporarily straighten the radiator to “set” the bend at the choke coil top.
Fishing for coax
The coil is then wound on the outside of the conduit and the remainder of the cable inserted through the bottom coil hole and pushed down. Using firm but careful manipulation, the cable is pushed and tugged through the exit hole until the coil is tightly wound and secure. This must be done without altering the bottom radiator length (you should continue to just see your ‘mark’ through the top hole.
Wound coil
At the top, cut a small (thin, narrow) notch in the edge of the conduit, pull the nylon line taut and nip the nylon line into the notch. Later, when an end cap is fitted, the cap will clamp the nylon line solidly in place and hold the radiator straight.
Fit a connector, measure the VSWR, if necessary trim the top element.
Measuring VSWR
However, you should find that very little trimming, if any, will be necessary. If you dual band the antenna, the 2m resonance will appear to shift upwards slightly. So, don’t be too concerned if your antenna at this stage appears to have its VSWR curve dip a bit below 146 MHz. The VSWR plot of the 2m Half-Wave antenna should look like the following:
VSWR plot of the 6m Half-Wave antenna
VSWR plot of the 2m Half-Wave antenna
When you are happy with the VSWR, finally, cap the top, securing the nylon line and the radiator in place.
Don’t block or seal the bottom end of the conduit. This is to allow condensation etc to drain away.

Tips

File the coil holes to ease the bends.
Filing the coil holesProfiled coil holes
Heatshrink the feedpoint to seal against water entry. Also heatshrink the coil’s entry and exit points to minimise water entry.
Heatshrinking the feedpoint
Heatshrink the bottom end to provide a buffer for the exiting coax and neaten the base.
Heatshrunk base

The type of Co-Ax is Important. Use braided co-ax only.

Do not use co-ax with a foil shield as the foil tends to break during assembly especially at the sharp bends at the choke entry/exit points. Obviously if this happens, your antenna will not work!

Cocky Proofing

To protect the choke coil from bird attacks especially from the White Cockatoos, the coil needs to be covered with a ‘Cocky’ shield. An empty Silicone Sealant cartridge (enlarge the hole at the top and cut the barrel to length) neatly fits over a 2m antenna coil. A PET soft-drink bottle can be used for larger coils which, when heated with a hot-air gun (but don‘t melt the conduit), will act like heat shrink tubing and become a very tough shield. Before fitting the shield, wrap PVC tape over the coil and the entry/exit holes to minimise water entry.

Using something other than grey electrical conduit

To the purist and his microwave oven, grey electrical conduit is considered lossy. It is, however, very UV resistant. The design compensates for the affect of the conduit by shortening the elements (by about a 2% factor) but otherwise the conduit appears to have little effect on the radiation efficiency.
If you use orange (HD) conduit, irrigation pipe, Telstra conduit, GRP, etc, the element lengths will be different. An unenclosed antenna will have longer elements (probably 2% or maybe 3% longer). Similarly, an antenna enclosed in something that is very much loaded with conductive filler will be much shorter (but, of course, don‘t ever use a material like this for an antenna).

Scaling to Other Frequencies

The above design will scale to other frequencies, the limitation being the mechanical properties of the conduit. To make an antenna for other frequencies, a suitable choke coil can be determined from this table.

RG58 Co-ax Self Resonant Frequency (MHz)
Coil Turns PVC Conduit Former Diameter
25mm 32mm 50mm
4 - 160 -
5 150 136 85
8 142 106 65
9 135 100 60
10 129 95 57
12 117 84 52
15 105 75 47

As a suggestion, construct a series of graphs from the data to make it easier to interpolate. Ideally, the choke should consist of unit turns. Half turns are OK but do not wind a choke coil using other than full or half turns. If your design is for a single operating frequency (or very narrow band) then chose the lowest half turn (ie the choke frequency is closer to the operating frequency); if, however, a broader-band antenna is required, chose the nearest higher half turn.
The choke needs to be resonant about 5 to 6% below the desired operating frequency. Closer spacing will sharpen (and deepen) the VSWR response; wider spacing flattens but raises the VSWR. curve.

6m Half Wave Flower Pot

To build a 6m version, use 50mm (OD) conduit. The dimensions are in the following diagram.
 6m Half-Wave antenna
6m version
VSWR plot of the 6m Half-Wave antenna
VSWR plot of the 6m Half-Wave antenna


Source : http://vk2zoi.com

Single 5/8 Flower Pot Antenna

The Single 5/8 version of the Flower Pot simply substitutes a 5/8 wave-length section for the top quarter wave of the basic half wave antenna design. The arrangement is shown in the sketch below. The 5/8λ radiator uses a 0.2λ (shorted) co-ax phasing stub to resonate the 5/8λ element. In a conventional 5/8λ mobile whip, an inductor is used to bring the 5/8λ element to resonance; however, in this Flower Pot style of antenna, using a co-ax phasing (or delay) stub suits the construction technique and has the advantage of being able to be precisely determined and cut at the construction stage.
The antenna configuration is similar to, but slightly shorter than, the “Gain Sleeve” antenna described in the RSGB Hand-book (6th Edition – figure 13.99, which itself is derived from the reactance – or shunt – fed 5/8λ monopole antenna at figure 13.84 of the handbook).
The Gain Sleeve antenna achieves an effective radiating element length of one wavelength and, since the aperture is twice that of a half wave dipole, a theoretical gain of 3dBd (gain over a dipole) could be achieved.
However, note that the Handbook indicates that in practice, the Gain Sleeve antenna would realise about 2.5dBd. The effective radiating element length of the Single 5/8 Flower Pot is 7/8λ suggesting it would have somewhat less than 2.5dBd gain.

2m Construction



2m Single 5/8 Flower Pot
Construction of the Single 5/8, whilst a little more involved than the basic half-wave antenna, is again fairly simple.
From the top of the co-ax, measure off an approximate 5/8λ distance to locate the position of the feed point. Make this distance slightly longer than the exact 5/8 length (say 10mm) as you will trim the top element to length later.
At the feed point, cut away the outer sheath and braid so as to form a 2-3mm gap.
From the edge of the gap, measure off the distance for the 0.2λ section. For solid polyethylene dielectric cable, this is 276mm for 2m and 755mm for 6m. From this point, expose sufficient braid to be able to make several pigtails to be soldered to the inner conductor and then the braid and outer sheath for the remainder of the top element length can be stripped off. At the 0.2λ point, cut into the inner dielectric to expose about 3mm of the inner conductor and solder the braid pigtails to the inner conductor.
Trim the top element to length. It will be most unlikely that you have to further trim the antenna later but you could leave a small, extra margin to allow some later adjustment if desired; however, builders of this antenna have reported that further trimming was unnecessary so you should have confidence in cutting the element to length at this stage.
To complete construction, follow the same procedure as for the half-wave antenna. As in the half wave version, use a length of nylon fishing line to pull the radiator taut and clamp it in place with the conduit cap. The length of the conduit above the choke can be 10 to 20mm longer than the total length of the quarter wave and 5/8 wave elements.
The Single 5/8 has a slightly sharper VSWR response than the basic half wave Flower Pot and, although a VSWR of less than 1.5:1 across the 2m band can be achieved, the antenna can be cut to favour the high FM portion of the band or the lower packet portion. The dimensions derived during my experiments for 2m are given in the following table; these dimensions have since been validated in further builds of the antenna.

Desired Portion of Band Upper 5/8 element Bottom “λ/4” Choke Coil
Across the Band 1228mm 465mm 9 turns on 25mm former
FM & Repeaters 1224mm 465mm
Packet low band 1236mm 480mm

The VSWR curves for the three antennae are shown in the next figure. Note that the “Across the Band” curve purposely favours the higher end of the 2m band.


VSWR curves for three antennae. Note that the "Across the Band" curve purposely favours the higher end of the 2m band.

6m Single 5/8 Version (and using the Antenna at Other Frequencies)

The physical/mechanical properties of conduit are not conducive to building a 6m or a lower frequency version of the single 5/8 antenna because conduit is not sufficiently rigid to maintain straightness and it retains a set after a hot day.
I have, however, built a 6m single 5/8 by terminating the top end of the phasing stub onto a standard mobile base mounted on a conduit cap and using a plain (braided) mobile whip for the remainder of the top 5/8 element. This way the conduit length is approximately halved and is less susceptible to bending. If you want to try building one doing this, the length of the whip will, depending on its diameter, probably be marginally longer than the equivalent length if it was made using the co-ax inner. Also when using a whip, the overall length of the 5/8 element will need to include the length of the phasing section. Otherwise, the dimensions readily scale from the 2m antenna.
The antenna can be scaled to any operating frequency using the choke data given previously. Note that the 2m single 5/8 is close on 2m long; 25mm conduit is mechanically OK for this length and this suggests that the ideal application of this style of antenna is for frequencies around 2m, ie boating, aircraft and the VHF two-way communications bands.
When working out the phasing stub length for other frequencies, don’t forget to take the velocity factor of the cable into consideration.

Source : http://vk2zoi.com

eQSO Rapi Gateway

Share eQSO Rapi Gateway Versi Terbaru

Cara Penggunaan :

  1. Harus Konek Internet 
  2. Dan Anda Harus Memasukkan CALLSIGN Anda
  3. Terus Pilih Channel
  4. Dan Tekan Pada Huruf " HUBUNGKAN "
  5. Untuk Pengguna Komputer Harus Mempunyai Headphone
  6. Tapi Kalau Laptop, Anda Bisa Memakai Langsung Tanpa Mempunyai Headphone Sudah Bisa
  7. Kecepatan Internet Minimal 128Kbps
  8. Dan Yang Terakhir Download Software Tersebut 
Mau Download Software Ini
: Tinggal Clik Link Dibawah Ini :


Semoga Software ini bermanfaat untuk rekan  WawasanElektronika semua & sukses terus rekan semua. 

Kode Etik dan Panca Bhakti RAPI

Kode Etik dan Panca Bhakti RAPI

Kode Etik
  1. Seorang anggota RAPI berjiwa Patuh
  2. Seorang anggota RAPI berjiwa Jujur
  3. Seorang anggota RAPI berjiwa Santun
  4. Seorang anggota RAPI berjiwa Tengang Rasa
  5. Seorang anggota RAPI berjiwa Tanggung Jawab
Terima Kasih untuk JZ04EBE atas masukan dan koreksinya

Panca Bhakti

  1. Seorang anggota RAPI harus rendah hati
  2. Seorang anggota RAPI harus energic
  3. Seorang anggota RAPI harus peka dan tanggap terhadap Aspek Sosial Kemasyarakatan
  4. Seorang anggota RAPI harus mempunyai daya juang yang menonjol pada Bangsa dan Negara Republik Indonesia
  5. Seorang anggota RAPI harus berjiwa Gotong Royong


Semoga Tips ini bermanfaat untuk rekan  WawasanElektronika semua & sukses terus rekan semua.

ALPHABET DALAM KOMUNIKASI RADIO

Alphabet Dalam Komunikasi Radio sebagai berikut:

A
:
ALPHA
B
:
BRAVO / BETA
C
:
CHARLIE
D
:
DELTA
E
:
ECHO
F
:
FOKSTROT / FOX
G
:
GOLF
H
:
HOTEL
I
:
INDIAN
J
:
JULIET
K
:
KILO
L
:
LIMA
M
:
MIKE
N
:
NOVEMBER / NANCY
O
:
OSCAR
P
:
PAPA
Q
:
QUEBEC
R
:
ROMEO
S
:
SIERA
T
:
TANGO
U
:
UNIFORM
V
:
VICTOR
W
:
WHISKEY
X
:
X-RAY
Y
:
YANKEE
Z
:
ZULLU


Semoga Tips ini bermanfaat untuk rekan  WawasanElektronika semua & sukses terus rekan semua.

Contoh Formulir SRP

FORMULIR SIMPATISAN RAPI (SRP) “E1025”
Radio Antar Penduduk Indonesia
Salam RAPI 5155,
Demi menjaga tertib administrasi dan tertib komunikasi pada jalur komunikasi elektronika RAPI diminta kepada para simpatisan/SRP dan calon anggota RAPI yang belum mempunyai 10-28 (callsign) agar mendaftarkan diri dengan mengisi form data diri yang telah disediakan untuk mendapatkan Nomor  SRP.
Nomor SRP ini berlaku selama 6 (enam) bulan sejak diterbitkan dan tidak dapat diperpanjang kembali. Untuk selanjutnya bagi yang telah mendapatkan nomor SRP diharapkan menghubungi sekretariat lokal/wilayah RAPI terdekat untuk mengurus 10-28 sebagai persyaratan berkomunikasi pada jalur komunikasi elektronika RAPI.
Apabila tetap dipergunakan pada jalur komunikasi elektronika RAPI setelah batas waktunya maka ADMIN akan melaksanakan penertiban (menonaktifkan IP dan ID address pada jalur komunikasi elektronika RAPI).
Formulir dikembalikan kepada ADMIN melalui email ke: zebra_jz21ak@yahoo.com dan rapielektronik@ymail.com

NAMA ASLI:JEPRI
ALAMAT  LENGKAP:JL,TIPAR CAKUNG,NO:22  RT/RW: 06/02 
Kel : SUKAPURA
Kec : CILINCING, JAKARTA UTARA
 
NO TLP:087886050417
EMAIL:SRP_1155.jakut@yahoo.co.id
FACEBOOK:

PERNYATAAN

:

1.    Melalui surat ini saya bersedia mengikuti peraturan/tatacara berkomunikasi yang telah ditetapkan oleh organisasi RAPI (Radio Antar Penduduk Indonesia) dan bersedia untuk di mute/kick (non aktifkan) oleh admin yang telah ditunjuk, dengan mengembalikan formulir ini berarti saya tunduk pada peraturan yang berlaku pada jalur komunikasi elektronika ini.
2.    Bahwa alamat dan nama yang saya tuliskan diatas sesuai KTP, pemegang SRP, dan bukan alamat orang lain.
10-28:SRP-0000                                                                    (diisi oleh admin)
BERLAKU:DD-MMMM-YYYY s/d DD-MMMM-YYYY                       (diisi oleh admin)
ADMIN:JZ21AK – Zebra/081345677021


Catatan:
  1. Nomor SRP ini hanya khusus dipakai untuk komunikasi jalur elektronika RAPI e1025
  1. Pemegang SRP tidak diperkenankan membuat interface untuk link gateway e1025

Demikian disampaikan dan untuk dapat dilaksanakan bersama.

Hormat kami,
(Team ADMIN Komunikasi Elektronika RAPI)

RAPI 10 CODE (Kode Sepuluh)

 RAPI TEN CODE (KODE SEPULUH) yang selalu digunakan dalam berkomunikasi sesama anggota RAPI:

10 - 1 Sulit didengar // Penerimaan buruk
10 - 2 Didengar jelas // Penerimaan baik
10 - 3 Berhenti mengudara / memancar
10 - 4 Benar // Dimengerti
10 - 5 Ada pesan untuk disampaikan
10 - 6 Sedang sibuk kecuali ada berita penting
10 - 7 Mengalami kerusakan // Tidak dapat mengudara
10 - 8 Tidak ada kerusakan // Dapat mengudara
10 - 9 Mohon diulangi
10 - 10 Penyampaian berita selesai
10 - 11 Berbicara terlalu cepat
10 - 12 Mengundurkan diri karena ada tamu
10 - 13 Laporan keadaan cuaca / jalanan
10 - 14 Informasi
10 - 15 Informasi sudah disampaikan
10 - 16 Mohon dijemput / diambil di ...
10 - 17 Ada urusan penting
10 - 18 Sesuatu untuk kita
10 - 19 Bukan untuk Anda, harap kembali
10 - 20 Lokasi // Posisi
10 - 21 Kontak / hubungan melalui telepon
10 - 22 Melapor langsung ke ...
10 - 23 Menunggu // Stand by
10 - 24 Selesai melaksanakan tugas
10 - 25 Dapatkah menghubungi / kontak dengan ...
10 - 26 Pesanan terakhir kurang diperhatikan
10 - 27 Pindah ke jalur / channel ...
10 - 28 Nama panggilan // Callsign
10 - 29 Waktu hubungan / kontak habis
10 - 30 Tidak menaati peraturan
10 - 31 Antena yang digunakan
10 - 32 Laporan sinyal dan modulasi // Radio check
10 - 33 KEADAAN DARURAT // EMERGENCY
10 - 34 Butuh bantuan, ada kesulitan di stasiun ini
10 - 35 INFORMASI RAHASIA
10 - 36 Jam berapa waktu yang tepat ?
10 - 37 PERLU MOBIL DEREK DI ...
10 - 38 PERLU AMBULANS DI ...
10 - 39 Pesan sudah disampaikan
10 - 40 PERLU DOKTER
10 - 41 Mohon pindah ke jalur / channel ...
10 - 42 ADA KECELAKAAN DI ...
10 - 43 Kemacetan lalu lintas di ...
10 - 44 Ada pesan untuk Anda
10 - 45 Dalam jangkauan mohon melapor
10 - 46 Memerlukan montir
10 - 50 Mohon kosongkan jalur / channel
10 - 60 Apakah ada pesan selanjutnya ?
10 - 62 Tidak dimengerti, melalui telepon saja
10 - 63 Tugas / pekerjaan dilanjutkan di ...
10 - 64 Pekerjaan telah selesai / bersih
10 - 65 Menunggu berita lanjutan
10 - 67 Semua unit setuju
10 - 69 Pesanan telah diterima
10 - 70 KEBAKARAN DI ...
10 - 71 Pesawat KRAP (RIG) yang dipakai
10 - 73 Kurangi kecepatan di ...
10 - 74 Tidak // Negatif
10 - 75 Penyebab gangguan
10 - 76 Dalam perjalanan ke ...
10 - 77 Belum / tidak menghubungi
10 - 81 Pesankan kamar di hotel ...
10 - 82 Pesankan kamar untuk ...
10 - 84 Nomor telepon
10 - 85 Alamat
10 - 89 Butuh montir radio
10 - 90 Gangguan pesawat televisi (TVI)
10 - 91 Bicara dekat mikropon
10 - 92 Pemancar perlu penyesuaian
10 - 93 Apakah frekuensi sudah tepat ?
10 - 94 Berbicara agak panjang
10 - 95 Mengudara dengan sinyal setiap 5 detik
10 - 97 Tes pada pemancar
10 - 99 Tugas selesai, semua orang selamat
10 - 100 Akan ke kamar mandi
10 - 200 BUTUH BANTUAN POLISI DI ...
10 - 300 BUTUH PEMADAM KEBAKARAN DI ...
10 - 400 BUTUH PETUGAS KETERTIBAN UMUM DI ...
10 - 500 BUTUH BANTUAN PROVOST DI ...
10 - 600 BUTUH BANTUAN GARNIZUN DI ...
10 - 700 BUTUH BANTUAN S.A.R. DI ...
10 - 800 BUTUH BANTUAN PERUSAHAAN LISTRIK DI ...

Semoga Tips ini bermanfaat untuk rekan  WawasanElektronika semua & sukses terus rekan semua.